recent research topics in optical communication

share this!

May 13, 2024

This article has been reviewed according to Science X's editorial process and policies . Editors have highlighted the following attributes while ensuring the content's credibility:

fact-checked

peer-reviewed publication

trusted source

Optical power evolution in fiber-optic networks: New framework for better modeling and control

With the emergence of internet services such as AI-generated content and virtual reality, the demand for global capacity has surged, significantly intensifying pressures on fiber-optic communication systems. To address this surge and reduce operational costs, efforts are underway to develop autonomous driving optical networks (ADONs) with highly efficient network operations.

One of the most important tasks for an ADON is to accurately model and control the optical power evolution (OPE) over fiber links, since it determines the level of impairment noise and signal transmission quality.

In fiber-optic communication systems, the optical power of signals evolves over the fiber and varies across different wavelengths, presenting a complex physical process, especially for multiband systems with severe Kerr nonlinearity and interchannel stimulated Raman scattering.

In multiband ADONs, OPE is mainly influenced by fiber propagation and amplification processes. In particular, the primary challenge in modeling and controlling OPE lies in optical amplifiers (OAs). Data-driven approaches are able to achieve high accuracy. However, traditional data-driven methods, especially neural networks (NNs), demand extensive data to construct accurate digital twin models, leading to significant measurement costs.

While some approaches can minimize required measurements through techniques like transfer learning or integrating physical knowledge, the perspective of data selection has received scant attention.

Recently, researchers from Shanghai Jiao Tong University (SJTU), Shanghai, China, proposed a Bayesian inference framework (BIF) to efficiently model and control the optical power evolutions in fiber-optic communication systems.

Their research is reported in Advanced Photonics in a paper titled "Digital twin modeling and controlling of optical power evolution enabling autonomous-driving optical networks: a Bayesian approach."

Leveraging Bayesian theory, the BIF selects the next to-be-measured spectrum/OA configuration by both the performance estimation and uncertainty analysis. This approach enables simultaneous exploitation and exploration of a data space to identify the most suitable candidates, thus reducing the requisite data size.

The researchers conducted extensive experiments and simulations in C+L-band fiber-optic transmission systems, to model and control the OPE with heterogenous OAs, including an erbium-doped fiber amplifier (EDFA) and a Raman amplifier (RA).

Compared with the NN-based modeling methods using randomly collected data, the proposed BIF can reduce the data needed for modeling by over 80% with an EDFA, and by over 60% with an RA. In terms of control, iterative adjustments of signal spectra and pump configurations were conducted, achieving arbitrary target gain/power spectra within fewer than 30 iterations.

This work provides an efficient approach to select data for measuring in a sequential manner. The measured data can be learned immediately to guide the next round of data collecting and optimization, thus achieving data-efficient modeling and controlling for OPE. Additionally, the probabilistic analysis of the proposed framework shows potential in reliability analysis for network operations, which is of vital importance for ADON.

According to corresponding author Prof. Qunbi Zhuge of SJTU, "The proposed framework can be a promising technical path for realizing data-driven ADON in future optical networks ."

Journal information: Advanced Photonics

Provided by SPIE

Explore further

Feedback to editors

Tiger beetles fight off bat attacks with ultrasonic mimicry

7 hours ago

Machine learning model uncovers new drug design opportunities

10 hours ago

Astronomers find the biggest known batch of planet ingredients swirling around young star

How 'glowing' plants could help scientists predict flash drought

11 hours ago

New GPS-based method can measure daily ice loss in Greenland

New candidate genes for human male infertility found by analyzing gorillas' unusual reproductive system

12 hours ago

Study uncovers technologies that could unveil energy-efficient information processing and sophisticated data security

13 hours ago

Scientists develop an affordable sensor for lead contamination

Chemists succeed in synthesizing a molecule first predicted 20 years ago

New optical tweezers can trap large and irregularly shaped particles

Relevant physicsforums posts, interference of two ultra short laser pulses, questions about the paraxial region for a single spherical surface.

May 12, 2024

Collimation of a Gaussian beam

May 10, 2024

It's still not clear to me what's the limit of light propagation

May 7, 2024

Factors that influence depth of field

May 3, 2024

Fourier Optics: Why a Plane Wave contributes to just a single point

Apr 24, 2024

More from Optics

Related Stories

Scientists build high power cladding-pumped Raman fiber laser at 1.2 μm waveband

Jan 30, 2024

Control of temperature dependent viscosity for manufacturing of Bi-doped active fiber

Apr 17, 2024

Researchers send data 4.5 million times faster than average broadband

Mar 26, 2024

Enhanced laser heterodyne spectroscopy helps atmospheric greenhouse gas measurements

Oct 24, 2023

Novel mathematical models illuminate light propagation in nonlinear optical fibers

Jan 24, 2022

Single-end hybrid Rayleigh Brillouin and Raman distributed fiber-optic sensing system

Jul 14, 2023

Recommended for you

Scientists create an 'optical conveyor belt' for quasiparticles

17 hours ago

Exploring the ultrasmall and ultrafast through advances in attosecond science

Scientists discover 'weird' statistics of electrons ejected by intense quantum light

New surface acoustic wave techniques could lead to surfing a quantum internet

Let us know if there is a problem with our content.

Use this form if you have come across a typo, inaccuracy or would like to send an edit request for the content on this page. For general inquiries, please use our contact form . For general feedback, use the public comments section below (please adhere to guidelines ).

Please select the most appropriate category to facilitate processing of your request

Thank you for taking time to provide your feedback to the editors.

Your feedback is important to us. However, we do not guarantee individual replies due to the high volume of messages.

E-mail the story

Your email address is used only to let the recipient know who sent the email. Neither your address nor the recipient's address will be used for any other purpose. The information you enter will appear in your e-mail message and is not retained by Phys.org in any form.

Newsletter sign up

Get weekly and/or daily updates delivered to your inbox. You can unsubscribe at any time and we'll never share your details to third parties.

More information Privacy policy

Donate and enjoy an ad-free experience

We keep our content available to everyone. Consider supporting Science X's mission by getting a premium account.

E-mail newsletter

Optical Communication: Its History and Recent Progress

• Open Access
• First Online: 14 December 2016

Cite this chapter

You have full access to this open access chapter

• Govind P. Agrawal 4  

63k Accesses

22 Citations

5 Altmetric

This chapter begins with a brief history of optical communication before describing the main components of a modern optical communication system. Specific attention is paid to the development of low-loss optical fibers as they played an essential role after 1975. The evolution of fiber-optic communication systems is described through its six generations over a 40-year time period ranging from 1975 to 2015. The adoption of wavelength-division multiplexing (WDM) during the 1990s to meet the demand fueled by the advent of the Internet is discussed together with the bursting of the telecom bubble in 2000. Recent advances brought by digital coherent technology and space-division multiplexing are also described briefly.

You have full access to this open access chapter,  Download chapter PDF

Similar content being viewed by others

Optical Transmission Technologies

Changing phases of fiber optic communication

The Future of Optical Communications

• Spectral Efficiency
• Optical Communication System
• Optical Receiver
• Repeater Spacing
• Submarine Cable

These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

1 Historical Perspective

The use of light for communication purposes dates back to antiquity if we interpret optical communication in a broad sense, implying any communication scheme that makes use of light. Most civilizations have used mirrors, fire beacons, or smoke signals to convey a single piece of information (such as victory in a war). For example, it is claimed that the Greeks constructed in 1084  b.c. a 500-km-long line of fire beacons to convey the news of the fall of Troy [ 1 ]. The chief limitation of such a scheme is that the information content is inherently limited and should be agreed upon in advance. Attempts were made throughout history to increase the amount of transmitted information. For example, the North American Indians changed the color of a smoke signal for this purpose. Similarly, shutters were used inside lighthouses to turn the beacon signal on and off at predetermined intervals. This idea is not too far from our modern schemes in which information is coded on the light emitted by a laser by modulating it at a high speed [ 2 ].

In spite of such clever schemes, the distance as well as the rate at which information could be transmitted using semaphore devices was quite limited even during the eighteenth century. A major advance occurred in 1792 when Claude Chappe came up with the idea of transmitting mechanically coded messages over long distances through the use of intermediate relay stations (10–15 km apart) that acted as repeaters in the modern-day language [ 3 ]. Figure  8.1 shows the inventor and his basic idea schematically. Chappe called his invention optical telegraph and developed a coding scheme shown in Fig.  8.1 to represent the entire alphabet through different positions of two needles. This allowed transmission of whole sentences over long distances. The first such optical telegraph was put in service in July 1794 between Paris and Lille (two French cities about 200 km apart). By 1830, the network had expanded throughout Europe [ 4 ]. The role of light in such systems was simply to make the coded signals visible so that they could be intercepted by the relay stations. The opto-mechanical communication systems of the nineteenth century were naturally slow. In modern-day terminology, the effective bit rate of such systems was less than 1 bit/s; a bit is the smallest unit of information in a binary system.

Claude Chappe, his coding scheme, and the mechanical device used for making optical telegraphs (licensed under Public Domain via Wikimedia Commons)

The advent of the electrical telegraph in the 1830s replaced the use of light by electricity and began the era of electrical communications [ 5 ]. The bit rate B could be increased to a few bits/s by using new coding techniques such as the Morse code. The use of intermediate relay stations allowed communication over long distances. Indeed, the first successful transatlantic telegraph cable went into operation in 1866. Telegraphy employed a digital scheme through two electrical pulses of different durations (dots and dashes of the Morse code). The invention of the telephone in 1876 brought a major change inasmuch as electric signals were transmitted in an analog form through a continuously varying electric current [ 6 ]. Analog electrical techniques dominated communication systems until the switch to optical schemes 100 years later.

The development of a worldwide telephone network during the twentieth century led to many advances in electrical communication systems. The use of coaxial cables in place of twisted wires increased system capacity considerably. The first coaxial-cable link, put into service in 1940, was a 3-MHz system capable of transmitting 300 voice channels (or a single television channel). The bandwidth of such systems was limited by cable losses, which increase rapidly for frequencies beyond 10 MHz. This limitation led to the development of microwave communication systems that employed electromagnetic waves at frequencies in the range of 1–10 GHz. The first microwave system operating at the carrier frequency of 4 GHz was put into service in 1948. Both the coaxial and microwave systems can operate at bit rates \( \sim \)  100 Mbit/s. The most advanced coaxial system was put into service in 1975 and operated at a bit rate of 274 Mbit/s. A severe drawback of high-speed coaxial systems was their small repeater spacing ( \( \sim \) 1 km), requiring excessive regeneration of signals and making such systems expensive to operate. Microwave communication systems generally allowed for a larger repeater spacing but their bit rate was also limited to near 100 Mbit/s.

All of the preceding schemes are now classified under the general heading of telecommunication systems. A telecommunication system transmits information from one place to another, whether separated by a few kilometers or by transoceanic distances. It may but does not need to involve optics. The optical telegraph of Claude Chappe can be called the first optical telecommunication system that spread throughout Europe over a 40-year period from 1800 to 1840. However, it was soon eclipsed by electrical telecommunication systems based on telegraph and telephone lines. By 1950, scientists were again looking toward optics to provide solutions for enhancing the capacity of telecommunication systems. However, neither a coherent optical source nor a suitable transmission medium was available during the 1950s. The invention of the laser and its demonstration in 1960 solved the first problem. Attention was then focused on finding ways for using laser light for optical communication. Many ideas were advanced during the 1960s [ 7 ], the most noteworthy being the idea of light confinement using a sequence of gas lenses [ 8 ].

Optical fibers were available during the 1960s and were being used for making gastroscope and other devices that required only a short length of the fiber [ 9 ]. However, no one was serious about using them for optical communication. The main problem was that optical fibers available during the 1960s had such high losses that only 10 % of light entering at one end emerged from the other end of a fiber that was only a few meters long. Most engineers ignored them for telecommunication applications where light had to be transported over at least a few kilometers. It was suggested in 1966 that losses of optical fibers could be reduced drastically by removing impurities from silica glass used to make them, and that such low-losses fibers might be the best choice for optical communication [ 10 ]. Indeed, Charles Kao was awarded one half of the 2009 noble prize for his groundbreaking achievements concerning the transmission of light in fibers for optical communication [ 11 ]. The idea of using glass fibers for optical communication was revolutionary since fibers are capable of guiding light in a manner similar to the confinement of electrons inside copper wires. As a result, they can be used in the same fashion as electric wires are used routinely.

However, before optical fibers could be used for optical communication, their losses had to be reduced to an acceptable level. This challenge was taken by Corning, an American company located not far from Rochester, New York where I work. A breakthrough occurred in 1970 when three Corning scientists published a paper indicating that they were able to reduce fiber losses to below 20 dB/km in the wavelength region near 630 nm [ 12 ]. Two years later, the same Corning team produced a fiber with a loss of only 4 dB/km by replacing titanium with germanium as a dopant inside the fiber’s silica core. Soon after, many industrial laboratories entered the race for reducing fiber losses even further. The race was won in 1979 by a Japanese group that was able to reduce the loss of an optical fiber to near 0.2 dB/km in the infrared wavelength region near 1.55 μm [ 13 ]. This value was close to the fundamental limit set by the phenomenon of Rayleigh scattering. Even modern fibers exhibit loss values similar to those first reported in 1979.

In addition to low-loss optical fibers, switching from microwaves to optical waves also required a compact and efficient laser, whose output could be modulated to impose the information that needed to be transmitted over such fibers. The best type of laser for this purpose was the semiconductor laser. Fortunately, at about the same time Corning announced its low-loss fiber in 1970, GaAs semiconductor lasers, operating continuously at room temperature, were demonstrated by two groups working in Russia [ 14 ] and at Bell Laboratories [ 15 ]. The simultaneous availability of compact optical sources and low-loss optical fibers led to a worldwide effort for developing fiber-optic communication systems [ 16 ].

The first-generation systems were designed to operate at a bit rate of 45 Mbit/s in the near-infrared spectral region because GaAs semiconductor lasers used for making them emit light at wavelengths near 850 nm. Since the fiber loss at that wavelength was close to 3 dB/km, optical signal needed to be regenerated every 10 km or so using the so-called repeaters. This may sound like a major limitation, but it was better than the prevailing coaxial-cable technology that required regeneration every kilometer or so. Extensive laboratory development soon led to several successful field trials. AT&T sent its first test signals on April 1, 1977 in Chicago’s Loop district. Three weeks later, General Telephone and Electronics sent live telephone traffic at 6 Mbit/s in Long Beach, California. It was followed by the British Post Office that began sending live telephone traffic through fibers near Martlesham Heath, UK. These trials were followed with further development, and commercial systems began to be installed in 1980. The new era of fiber-optic communication systems had finally arrived. Although not realized at that time, it was poised to revolutionize how humans lived and interacted. This became evident only after the advent of the Internet during the decade of the 1990s.

Increase in the BL product during the period 1840–2015. The emergence of new technologies is marked by red squares . Dashed line shows the trend as an aid for the eye. Notice the change in slope around 1977 when optical fibers were first used for optical communications

A commonly used figure of merit for communication systems is the bit rate–distance product BL , where B is the bit rate and L is the repeater spacing, the distance after which an optical signal must be regenerated to maintain its fidelity [ 2 ]. Figure  8.2 shows how the BL product has increased by a factor of 10 18 through technological advances during the last 180 years. The acronym WDM in this figure stands for wavelength-division multiplexing, a technique used after 1992 to transmit multiple channels at different wavelengths through the same fiber. Its use enhanced the capacity of fiber-optic communication systems so dramatically that data transmission at 1 Tbit/s was realized by 1996. The acronym SDM stands for space-division multiplexing, a technique used after 2010 to further enhance the capacity of fiber-optic systems in response to continuing increase in the Internet data traffic (with the advent of video streaming by companies such as YouTube and Netflix) and fundamental capacity limitations of single-mode fibers (see Sect.  8.5 ). Two features of Fig.  8.2 are noteworthy. First, a straight line in this figure indicates an exponential growth because of the use of logarithmic scale for the data plotted on the y axis. Second, a sudden change in the line’s slope around 1977 indicates that the use of optical fibers accelerated the rate of exponential growth and signaled the emergence of a new optical communication era.

2 Basic Concepts Behind Optical Communication

Before describing the technologies used to advance the state of the art of fiber-optic communication systems, it is useful to look at the block diagram of a generic communication system in Fig.  8.3 a. It consists of an optical transmitter and an optical receiver connected to the two ends of a communication channel that can be a coaxial cable (or simply air) for electric communication systems but takes the form of an optical fiber for all fiber-optic communication systems.

2.1 Optical Transmitters and Receivers

The role of optical transmitters is to convert the information available in an electrical form into an optical form, and to launch the resulting optical signal into a communication channel. Figure  8.3 b shows the block diagram of an optical transmitter consisting of an optical source, a data modulator, and electronic circuitry used to derive them. Semiconductor lasers are commonly used as optical sources, although light-emitting diodes (LEDs) may also be used for some less-demanding applications. In both cases, the source output is in the form of an electromagnetic wave of constant amplitude. The role of the modulator is to impose the electrical data on this carrier wave by changing its amplitude, or phase, or both of them. In the case of some less-demanding applications, the current injected into a semiconductor laser itself is modulated directly, alleviating the need of an expensive modulator.

( a ) A generic optical communication system. ( b ) Components of an optical transmitter. ( c ) Components of an optical receiver

The role of optical receivers is to recover the original electrical data from the optical signal received at the output end of the communication channel. Figure  8.3 c shows the block diagram of an optical receiver. It consists of a photodetector and a demodulator, together with the electronic circuitry used to derive them. Semiconductor photodiodes are used as detectors because of their compact size and low cost. The design of the demodulator depends on the modulation scheme used at the transmitter. Many optical communication systems employ a binary scheme referred to as intensity modulation with direct detection. Demodulation in this case is done by a decision circuit that identifies incoming bits as 1 or 0, depending on the amplitude of the electric signal. All optical receivers make some errors because of degradation of any optical signal during its transmission and detection, shot noise being the most fundamental source of noise. The performance of a digital lightwave system is characterized through the bit-error rate. It is customary to define it as the average probability of identifying a bit incorrectly. The error-correction codes are sometimes used to improve the raw bit-error rate of an optical communication system.

2.2 Optical Fibers and Cables

Most people are aware from listening to radios or watching televisions that electromagnetic waves can be transmitted through air. However, optical communication systems require electromagnetic waves whose frequencies lie in the visible or near-infrared region. Although such waves can propagate through air over short distances in good weather conditions, this approach is not suitable for making optical communication networks spanning the whole world. Optical fibers solve this problem and transmit light over long distances, irrespective of weather conditions, by confining the optical wave to the vicinity of a microscopic cylindrical glass core through a phenomenon known as total internal reflection .

Internal structure of a single-mode fiber; typical size of each part is indicated. A spool of such fiber is also shown (licensed under Public Domain via Wikimedia Commons)

Figure  8.4 shows the structure of an optical fiber designed to support a single spatial mode by reducing its core diameter to below 10 μm. In the case of a graded-index multimode fiber the core diameter is typically 50 μm. The core is made of silica glass and is doped with germania to enhance its refractive index slightly (by about 0.5 %) compared to the surrounding cladding that is also made of silica glass. A buffer layer is added on top of the cladding before putting a plastic jacket. The outer diameter of the entire structure, only a fraction of a millimeter, is so small that the fiber is barely visible. Before it can be used to transmit information, one or more optical fibers are enclosed inside a cable whose diameter may vary from 1 to 20 mm, depending on the intended application.

Wavelength dependence of power losses measured in 1979 for a low-loss silica fiber [ 13 ]. Various lines show the contribution of different sources responsible for losses (from [ 2 ]; ©2010 Wiley)

What happens to an optical signal transmitted through an optical fiber? Ideally, it should not be modified by the fiber at all. In practice, it becomes weaker because of unavoidable losses and is distorted through the phenomena such as chromatic dispersion and the Kerr nonlinearity [ 2 ]. As discussed earlier, losses were the limiting factor until 1970 when a fiber with manageable losses was first produced [ 12 ]. Losses were reduced further during the decade of 1970s, and by 1979 they have been reduced to a level as low as 0.2 dB/km at wavelengths near 1.55 μm. Figure  8.5 shows the wavelength dependence of power losses measured for such a fiber [ 13 ]. Multiple peaks in the experimental curve are due to the presence of residual water vapors. The dashed line, marked Rayleigh scattering, indicates that, beside water vapors, most of the loss can be attributed to the fundamental phenomenon of Rayleigh scattering, the same one responsible for the blue color of our sky. Indeed, although water peaks have nearly disappeared in modern fibers, their losses have not changed much as they are still limited by Rayleigh scattering.

2.3 Modulations Formats

The first step in the design of any optical communication system is to decide how the electrical binary data would be converted into an optical bit stream. As mentioned earlier, an electro-optic modulator is used for this purpose. The simplest technique employs optical pulses such that the presence of a pulse in the time slot of a bit corresponds to 1, and its absence indicates a 0 bit. This is referred to as on–off keying since the optical signal is either “off” or “on” depending on whether a 0 or 1 bit is being transmitted.

Digital bit stream 010110 … coded by using ( a ) return-to-zero (RZ) and ( b ) nonreturn-to-zero (NRZ) formats

There are still two choices for the format of the resulting optical bit stream. These are shown in Fig.  8.6 and are known as the return-to-zero (RZ) and nonreturn-to-zero (NRZ) formats. In the RZ format, each optical pulse representing bit 1 is shorter than the bit slot, and its amplitude returns to zero before the bit duration is over. In the NRZ format, the optical pulse remains on throughout the bit slot, and its amplitude does not drop to zero between two or more successive 1 bits. As a result, temporal width of pulses varies depending on the bit pattern, whereas it remains the same in the case of RZ format. An advantage of the NRZ format is that the bandwidth associated with the bit stream is smaller by about a factor of 2 simply because on–off transitions occur fewer times. Electrical communication systems employed the NRZ format for this reason in view of their limited bandwidth. The bandwidth of optical communication systems is large enough that the RZ format can be used without much concern. However, the NRZ format was employed initially. The switch to the RZ format was made only after 1999 when it was found that its use helps in designing high-capacity lightwave systems. By now, the RZ format is use almost exclusively for WDM systems whose individual channels are designed to operate at bit rates exceeding 10 Gbit/s.

2.4 Channel Multiplexing

Before the advent of the Internet, telephones were used most often for communicating information. When an analog electric signal representing human voice is digitized, the resulting digital signal contains 64,000 bits over each one second duration. The bit rate of such an optical bit stream is clearly 64 kbit/s. Since fiber-optic communication systems are capable of transmitting at bit rates of up to 40 Gbit/s, it would be a huge waste of bandwidth if a single telephone call was sent over an optical fiber. To utilize the system capacity fully, it is necessary to transmit many voice channels simultaneously through multiplexing. This can be accomplished through time-division multiplexing (TDM) or WDM. In the case of TDM, bits associated with different channels are interleaved in the time domain to form a composite bit stream. For example, the bit slot is about 15 μs for a single voice channel operating at 64 kb/s. Five such channels can be multiplexed through TDM if the bit streams of successive channels are delayed by 3 μs. Figure  8.7 a shows the resulting bit stream schematically at a composite bit rate of 320 kb/s. In the case of WDM, the channels are spaced apart in the frequency domain. Each channel is carried by its own carrier wave. The carrier frequencies are spaced more than the channel bandwidth so that the channel spectra do not overlap, as seen in Fig.  8.7 b. WDM is suitable for both analog and digital signals and is used in broadcasting of radio and television channels. TDM is readily implemented for digital signals and is commonly used for telecommunication networks.

( a ) Time-division multiplexing of five digital voice channels operating at 64 kb/s. ( b ) Wavelength-division multiplexing of three analog or digital signals

The concept of TDM has been used to form digital hierarchies. In North America and Japan, the first level corresponds to multiplexing of 24 voice channels with a composite bit rate of 1.544 Mb/s (hierarchy DS-1), whereas in Europe 30 voice channels are multiplexed, resulting in a composite bit rate of 2.048 Mb/s. The bit rate of the multiplexed signal is slightly larger than the simple product of 64 kb/s with the number of channels because of extra control bits that are added for separating channels at the receiver end. The second-level hierarchy is obtained by multiplexing four DS-1 channels. This results in a bit rate of 6.312 Mb/s (hierarchy DS-2) for North America and 8.448 Mb/s for Europe. This procedure is continued to obtain higher-level hierarchies.

The lack of an international standard in the telecommunication industry during the 1980s led to the advent of a new standard, first called the synchronous optical network (SONET) and later termed the synchronous digital hierarchy (SDH). It defines a synchronous frame structure for transmitting TDM digital signals. The basic building block of the SONET has a bit rate of 51.84 Mbit/s. The corresponding optical signal is referred to as OC-1, where OC stands for optical carrier. The basic building block of the SDH has a bit rate of 155.52 Mbit/s and is referred to as STM-1, where STM stands for a synchronous transport module. A useful feature of the SONET and SDH is that higher levels have a bit rate that is an exact multiple of the basic bit rate. Table  8.1 lists the correspondence between SONET and SDH bit rates for several levels. Commercial STM-256 (OC-768) systems operating near 40 Gbit/s became available by 2002. One such optical channel transmits more than half million telephone conversations over a single optical fiber. If the WDM technique is employed to transmit 100 channels at different wavelengths, one fiber can transport more than 50 million telephone conversations at the same time.

3 Evolution of Optical Communication from 1975 to 2000

As mentioned earlier, initial development of fiber-optic communication systems started around 1975. The enormous progress realized over the 40-year period extending from 1975 to 2015 can be grouped into several distinct generations. Figure  8.8 shows the increase in the BL product over the period 1975–2000 as quantified through various laboratory experiments [ 17 ]. The straight line corresponds to a doubling of the BL product every year. The first four generations of lightwave systems are indicated in Fig.  8.8 . In every generation, the BL product increases initially but then begins to saturate as the technology matures. Each new generation brings a fundamental change that helps to improve the system performance further.

Increase in the BL product over the period 1975–2000 through several generations of optical communication systems. Different symbols are used for successive generations (from [ 2 ]; ©2010 Wiley)

3.1 The First Three Generations

The first generation of optical communication systems employed inside their optical transmitters GaAs semiconductor lasers operating at a wavelength near 850 nm. The optical bit stream was transmitted through graded-index multimode fibers before reaching an optical receiver, where it was converted back to the electric domain using a silicon photodetector. After several field trials during the period 1977–1979, such systems became available commercially in the year 1980. They operated at a bit rate of 45 Mbit/s and allowed repeater spacings of up to 10 km. The larger repeater spacing compared with 1-km spacing of coaxial systems was an important motivation for system designers because it decreased the installation and maintenance costs associated with each repeater. It is important to stress that even the first-generation systems transmitted nearly 700 telephone calls simultaneously over a single fiber through the use of TDM.

It was evident to system designers that the repeater spacing could be increased considerably by operating the system in the infrared region near 1.3 μm, where fiber losses were below 1 dB/km (see Fig.  8.5 ). Furthermore, optical fibers exhibit minimum dispersion in this wavelength region. This realization led to a worldwide effort for the development of new semiconductor lasers and detectors based on the InP material and operating near 1.3 μm. The second generation of fiber-optic communication systems became available in the early 1980s, but their bit rate was initially limited to 100 Mbit/s because of dispersion in multimode fibers. This limitation was overcome by the use of single-mode fibers. In such fibers the core diameter is reduced to near 10 μm (see Fig.  8.4 ) so that the fiber supports a single spatial mode. A laboratory experiment in 1981 demonstrated transmission at 2 Gbit/s over 44 km of a single-mode fiber. The introduction of commercial systems soon followed. By 1987, such second-generation commercial systems were operating at bit rates of up to 1.7 Gbit/s with a repeater spacing of about 50 km.

The repeater spacing of the second-generation systems was still limited by the fiber loss at their operating wavelength of 1.3 μm. As seen in Fig.  8.5 , losses of silica fibers become the smallest at wavelengths near 1.55 μm. However, the introduction of third-generation optical communication systems operating at 1.55 μm was considerably delayed by a relatively large dispersion of single-mode fibers in this spectral region. Conventional InGaAsP semiconductor lasers could not be used because of pulse spreading occurring as a result of simultaneous oscillation of multiple longitudinal modes. This dispersion problem could be solved either by using dispersion-shifted fibers designed to have minimum dispersion near 1.55 μm, or by designing lasers such that their spectrum contained a dominant single longitudinal mode. Both approaches were followed during the 1980s. By 1985, laboratory experiments indicated the possibility of transmitting information at bit rates of up to 4 Gbit/s over distances in excess of 100 km. Third-generation optical communication systems operating at 2.5 Gbit/s became available commercially in 1990, and their bit rate was soon extended to 10 Gbit/s. The best performance was achieved using dispersion-shifted fibers in combination with lasers oscillating in a single longitudinal mode.

A relatively large repeater spacing of the third-generation 1.55-μm systems reduced the need of signal regeneration considerably. However, economic pressures demanded further increase in its value of close to 100 km. It was not immediately obvious how to proceed since losses of silica fibers at 1.55 μm were limited to near 0.2 dB/km by the fundamental process of Rayleigh scattering. One solution was to develop more sensitive optical receivers that could work reliably at reduced power levels. It was realized by many scientists that repeater spacing could be increased by making use of a heterodyne-detection scheme (similar to that used for radio- and microwaves) because its use would require less power at the optical receiver. Such systems were referred to as coherent lightwave systems and were under development worldwide during the 1980s. However, the deployment of such systems was postponed with the advent of fiber amplifiers in 1989 that were pumped optically using semiconductor lasers and were capable of boosting the signal power by a factor of several hundreds.

3.2 The Fourth Generation

By 1990 the attention of system designers shifted toward using three new ideas: (1) periodic optical amplification for managing fiber losses, (2) periodic dispersion compensation for managing fiber dispersion, and (3) WDM for enhancing the system capacity. As seen in Fig.  8.9 , the WDM technique employs multiple lasers at slightly different wavelengths such that multiple data streams are transmitted simultaneously over the same optical fiber. The basic idea of WDM was not new as this technique was already being used at the radio- and microwave frequencies (e.g., by the television industry). However, its adoption at optical wavelengths required the development of a large number of new devices over a time span of a few years. For example, optical multiplexers and demultiplexers that could combine and separate individual channels at the two ends of a fiber link were critical components for the advent of the WDM systems.

Schematic of a WDM communication system. Multiple transmitters operating at different wavelengths are combined using a multiplexer and all channels are sent simultaneously over the same optical fiber. A demultiplexer at the receiving end separates individual channels and sends them to different receivers

The fourth generation of optical communication systems made use of optical amplifiers for increasing the repeater spacing, in combination with the WDM technique for increasing the system capacity. As seen in Fig.  8.8 , the advent of the WDM technique around 1992 started a revolution that resulted in doubling of the system capacity every 8 months or so and led to lightwave systems operating at a bit rate of 1 Tbit/s by 1996. In most WDM systems, fiber losses are compensated periodically using erbium-doped fiber amplifiers spaced 60–80 km apart. Such WDM systems operating at bit rates of up to 80 Gbit/s were available commercially by the end of 1995. The researchers worldwide were pushing the limit of WDM technology. By 1996, three research groups reported during a post-deadline session of the Optical Fiber Communications conference that they were able to operate WDM systems with the total capacity of more than 1 Tbit/s. This represented an increase in the system capacity by a factor of 400 over a period of just 6 years!

The emphasis of most WDM systems is on transmitting as many optical channels as possible over a single fiber by adding more and more lasers operating at different wavelengths. The frequency spacing between two neighboring channels is chosen to be as small as possible but it has to be larger than the bandwidth of each channel. At a bit rate of 40 Gbit/s, a channel spacing of 50 GHz is the smallest that can be used. The standard setting agency, ITU, has assigned a set of fixed frequencies for commercial WDM systems using this 50-GHz channel spacing. All these frequencies lie in the wavelength region near 1550 nm where fiber losses are the smallest. The wavelength range of 1530–1570 nm is called the C band (C standing for conventional), and most commercial WDM systems are designed to work in this band. However, the S and L bands lying on the short- and long-wavelength side of the C band, respectively, are also used if necessary. This approach led in 2001 to a 11-Tbit/s experiment in which 273 channels, each operating at 40 Gbit/s, were transmitted over a distance of 117 km [ 18 ]. Given that the first-generation systems had a capacity of 45 Mbit/s in 1980, it is remarkable that the use of WDM increased the system capacity by a factor of more than 200,000 over a period of 21 years.

3.3 Bursting of the Telecom Bubble in 2000

It should be clear from Fig.  8.8 and the preceding discussion that the adoption of WDM during the fourth generation of optical communication systems was a disruptive technology. Fortunately, its adoption coincided with the advent and commercialization of the Internet around 1994. Just as the explosive growth of websites all around the world increased the volume of data flowing through the telecommunication networks, the fourth generation of optical communication systems making use of the WDM technology became available. Its advent allowed telecom operators to manage the data traffic by simply adding more channels to an existing WDM system. The demand went through the roof during the 4-year span of 1996–2000, and it led to a stock-market bubble that is now referred to as the telecom bubble.

The formation of the telecom bubble was the result of a rapid growth after 1995 in the telecommunication business. The stocks of companies dealing with the manufacturing and delivery of telecom services soared after 1995. As an example, consider the company JDS–Fitel involved in selling various optical devices needed for telecom systems. Its stock value was around $8 in June 1994, jumped to near $20 in June 1995, and exceeded $70 in June 1996 when the stock was split by 2:1 to bring the price near $35. The stock was split again in November 1997 when its price doubled a second time. In early 1999 the company announced a merger with Uniphase, another fast-growing optics company, resulting in the formation of JDSU. During that year, the stock of JDSU was increasing so rapidly that it was split two more times. Figure  8.10 shows how the stock price of JDSU varied over the 8-year period ranging from 1996 to 2004 after taking into account multiple splits. A nearly exponential growth during the 1999 indicates the formation of the telecom bubble during that year. A similar growth occurred in the stock price of many other telecommunication and Internet companies.

Price of JDSU stock over a period extending from January 1996 to January 2004. A sharp rise in price during the year 1999 is followed by a sharp decline after July 2001 ( source : public domain data)

The telecom bubble burst during the year 2000, and the stock prices of all telecommunication companies collapsed soon after, including that of JDSU as seen in Fig.  8.10 . Several companies went out of business and many surviving were in trouble financially. Commercial WDM systems capable of operating at 1 Tbit/s were still being sold, but their was no buyer for them. The research and development of fiber-optic communications systems slowed down to a crawl as everyone waited for the revival of the telecom industry. It took nearly 5 years before the US economy recovered, only to crash again in August 2008 owing to the formation of another bubble, this time in the real-estate market. One can say that the decade of 2000–2009 has not been a kind one as far as the telecommunication industry is concerned.

4 The Fifth Generation

In spite of the two severe economical downturns, considerable progress has occurred since 2000 in designing advanced optical communication systems, leading to the fifth and sixth generations of such systems. The focus of fifth-generation systems was on making the WDM systems more efficient spectrally. This was accomplished by reviving the coherent detection scheme that was studied in the late 1980s but abandoned soon after fiber-based optical amplifiers became available. Coherent receivers capable of detecting both the amplitude and phase of an optical signal through a heterodyne scheme were developed soon after the year 2000. Their commercial availability near the end of the decade allowed system designers to employ advanced modulation formats in which information is encoded using both the amplitude and phase of an optical carrier.

Constellation diagrams for ( a ) ASK, ( b ) PSK, ( c ) QPSK, and ( d ) multilevel QPSK formats

The basic concept can be understood from Fig.  8.11 , showing four modulation formats using the so-called constellation diagram that displays the real and imaginary parts of the complex electric field along the x and y axes, respectively. The first configuration represents the standard binary format, called amplitude-shift keying (ASK), in which the amplitude or intensity of the electric field takes two values, marked by circles and representing 0 and 1 bits of a digital signal. The second configuration is another binary format, called phase-shift keying (PSK), in which the amplitude remains constant but phase of the electric field takes two values, say 0 and π , that represent the 0 and 1 bits of a digital signal. The third configuration in part (c) of Fig.  8.11 shows the quaternary PSK (or QPSK) format in which the optical phase takes four possible values. This case allows to reduce the signal bandwidth since two bits can be transmitted during each time slot, and the effective bit rate is halved. Borrowing from microwave communication terminology, the reduced bit rate is called the symbol rate (or baud). The last example in Fig.  8.11 shows how the symbol concept can be extended to multilevel signaling such that each symbol carries 4 bits or more. An additional factor of two can be gained if one transmits two orthogonally polarized symbols simultaneously during each symbol slot, a technique referred to as polarization division multiplexing.

The concept of spectral efficiency, defined as the number of bits transmitted in 1 s within a 1-Hz bandwidth, is quite useful in understanding the impact of coherent detection in combination with phase-encoded modulation formats. The spectral efficiency of fourth generation WDM systems that employed ASK as the modulation format was limited to below 0.8 bit/s/Hz since at most 40 billion bits/s could be transmitted over a 50-GHz bandwidth of each WDM channel. This value for the fifth-generation systems can easily exceed 3 by using polarization multiplexing in combination with the QPSK format. Figure  8.12 shows how the spectral efficiency of optical communication systems has evolved since 1990 when its value was near 0.05 bit/s/Hz. Values near 2 bit/s/Hz were realized by 2005 and they approached 10 bit/s/Hz by the year 2010 [ 19 ].

Evolution of spectral efficiency after 1990 through laboratory demonstrations. The red star shows the fundamental capacity limit of optical fibers (after [ 19 ]; ©2012 IEEE)

The availability of coherent receivers and increased computing speeds led to another advance after it was realized that one can use digital signal processing to improve the signal-to-noise ratio (SNR) of an optical signal arriving at the receiver. Since a coherent receiver detects both the amplitude and the phase of an optical signal, together with its state of polarization, one has in essence a digital representation of the electric field associated with the optical signal. As a result, special electronic chips can be designed to process this digital signal that can compensate for the degradation caused by such unavoidable factors as fiber dispersion. One can also implement error-correcting codes and employ encoder and decoder chips to improve the bit-error rate at the receiver end. A new record was set in 2011 when 64-Tbit/s transmission was realized over 320 km of a single-mode fiber using 640 WDM channels that spanned both the C and L bands with 12.5-GHz channel spacing [ 20 ]. Each channel contained two polarization-multiplexed 107-Gbit/s signals coded with a modulation format known as quadrature amplitude modulation. Such techniques are routinely implemented in modern optical communication systems.

5 The Sixth Generation

As the capacity of WDM systems approached 10 Tbit/s, indicating that 10 trillion bits could be transmitted each second over a single piece of optical fiber supporting a single optical mode inside its tiny core (diameter about 10 μm), scientists began to think about the ultimate information capacity of a single-mode fiber. The concept of the channel capacity C was first introduced by Shannon in a 1948 paper [ 21 ] in which he showed that the SNR sets the fundamental limit for any linear communication channel with a finite bandwidth W through the remarkably simple relation \( C=W{ \log}_2\left(1+SNR\right) \) . The spectral efficiency, defined as \( SE=C /\ W \) , is thus only limited by the SNR of the received signal and can, in principle, be increased indefinitely by sending more and more powerful signals over the channel. Unfortunately, this conclusion does not hold for optical fibers that are inherently nonlinear and affect the bit stream propagating through them in a nonlinear fashion [ 2 ].

5.1 Capacity Limit of Single-Mode Fibers

Considerable attention was paid during the decade of 2000 to estimating the ultimate capacity of single-mode fibers in the presence of various nonlinear effects. In a paper published in 2010 Essiambre et al. were able to develop a general formalism for calculating it [ 22 ]. Figure  8.13 shows how the nonlinear effects reduce the spectral efficiency from its value predicted by Shannon’s relation, when high signal powers are launched to ensure a high SNR at the receiver. As one may expect, the spectral efficiency depends on the transmission distance, and it becomes worse as this distance increases. However, the most noteworthy feature of Fig.  8.13 is that, for any transmission distance, spectral efficiency is maximum at an optimum value of SNR that changes with distance. For example, the spectral efficiency of a 1000-km-long link is limited to 8 bit/s/Hz for single polarization, irrespective of the modulation format employed. This is in sharp contrast to the prediction of Shannon and reflects a fundamental limitation imposed by the nonlinear effects.

Spectral efficiency as a function of SNR calculated numerically including the nonlinear effects over transmission distances ranging from 500 to 8000 km (after [ 22 ]; ©2010 IEEE)

We can use the results shown in Fig.  8.13 to estimate the ultimate capacity of a single-mode fiber. The usable bandwidth of silica fibers in the low-loss window centered around 1550 nm is about 100 nm. This value translates into a channel bandwidth of 12.5 THz. Using this value and a peak spectral efficiency of about 16 bit/s/Hz (assuming polarization-division multiplexing), the maximum capacity of a single-mode fiber is estimated to be 200 Tb/s. This is an enormous number and was thought to be high enough until recently that system designers did not worry about running out of capacity. However, data traffic over fiber-optic networks has experienced a steady growth, doubling every 18 months, since the advent of the Internet in the early 1990s. The growth has even accelerated in recent years owing to the new activities such as video streaming. One way to meet the demand would be to deploy more and more fiber cables. However, this approach will result in a larger and larger fraction of the total electrical power being devoted to supporting optical transport networks. It is estimated that by 2025 the energy demand of modern telecommunication systems will consume a very large fraction of the total US energy budget, unless a way is found to design energy efficient optical networks.

5.2 Space-Division Multiplexing

One proposed solution makes use of space-division multiplexing (SDM) to increase the capacity of fiber-optic communication networks at a reduced energy cost per transmitted bit [ 23 – 26 ]. The basic idea is to employ multimode fibers such that several WDM bit streams can be transmitted over different modes of the same fiber. The energy advantage comes from integrating the functionalities of key optical components into a smaller number of devices. For instance, if a single multimode optical amplifier is used to amplify all spatially multiplexed bit streams, power consumption is likely to be lower compared to using separate amplifiers. For this reason, the SDM technique is attracting increasing attention since 2010, and several record-setting experiments have already been performed. Most of them employ multicore fibers in which several cores share the same cladding. Each core is typically designed to support a single mode but that is not a requirement. Figure  8.14 shows schematically the basic idea behind SDM using the case of a three-core fiber as an example.

Schematic illustration of the basic idea behind the SDM technique. WDM signals from different transmitters enter different cores or modes of a multimode fiber and are processed at the other end by different coherent receivers; DSP stands for digital signal processing (courtesy of S. Mumtaz)

Similar to the case of WDM technology, the implementation of SDM requires not only new types of fibers but also many other active and passive optical components such as mode multiplexers/demultiplexers and fiber amplifiers that can amplify signals in all modes/cores simultaneously. A lot of progress has been made since 2010 in realizing such devices and many laboratory demonstrations have shown the potential of SDM for enhancing the system capacity [ 23 – 26 ]. Figure  8.15 shows how the capacity of optical communication systems has evolved over a period ranging from 1980 to 2015 and covering all six generations. Single-wavelength systems, employing TDM in the electrical domain, started with a capacity of under 100 Mbit/s in the 1980s and were operating at 10 Gb/s around 1990. The advent of WDM in the early 1990 led to a big jump in the system capacity and subsequent adoption of coherent detection with digital signal processing allowed the capacity to reach 64 Tbit/s by the year 2010 [ 20 ]. Further increase in system capacity required the adoption of SDM. In a 2012 experiment, SDM was used to demonstrate data transmission at 1000 Tbit/s (or 1 Pbit/s) by employing a 12-core fiber [ 24 ]. Each fiber core carried 222 WDM channels, and each wavelength transmitted a 380-Gbit/s bit stream over a 52-km-long multicore fiber with a spectral efficiency of 7.6 bit/s/Hz.

Increase in the capacity of optical communication systems (on a logarithmic scale) realized from 1980 to 2015 using three different multiplexing techniques. Note the change in the slope around 1995 and 2011 when the WDM and SDM techniques were adopted (courtesy of R.J. Essiambre)

The simplest SDM case corresponds to a multicore fiber whose cores are far enough apart that they experience little coupling. In this situation, WDM signals in each core travel independently, and the situation is analogous to using separate fibers. Indeed, most high-capacity experiments have employed this configuration through multicore fibers with 7, 12, or 19 cores. In a second category of experiments single-core fibers supporting a few spatial modes are employed [ 23 ]. In this case, modes become invariably coupled, both linearly and nonlinearly, since all channels share the same physical path. Degradations induced by linear coupling are then removed at the receiver end through digital signal processing. In a 2015 experiment, a fiber supporting 15 spatial modes was used to transmit 30 polarization-multiplexed channels over 23 km [ 27 ].

6 Worldwide Fiber-Optic Communication Network

The advent of the Internet in the early 1990s made it necessary to develop a worldwide network capable of connecting all computers (including cell phones) in a transparent manner. Such a network required deployment of fiber-based submarine cables across all oceans. The first such cable was installed in 1988 across the Atlantic ocean (TAT–8) but it was designed to operate at only 280 Mbit/s using the second-generation technology. The same technology was used for the first transpacific fiber-optic cable (TPC–3), which became operational in 1989. By 1990 the third-generation lightwave systems had been developed. The TAT–9 submarine system used this technology in 1991; it was designed to operate near 1.55 μm at a bit rate of 560 Mb/s with a repeater spacing of about 80 km. The increasing traffic across the Atlantic Ocean led to the deployment of the TAT–10 and TAT–11 cables by 1993 with the same technology. A submarine cable should be strong so that it can withstand biting by large sea animals. Figure  8.16 shows, as an example, the internal structure of a submarine cable containing several fibers for carrying bidirectional traffic. Optical fibers are immersed in a water-resistant jelly that is surrounded with many steel rods to provide strength. Steel rods are kept inside a copper tube that itself is covered with the insulating polyethylene. As the scale on the right side of Fig.  8.16 shows, the outer diameter of the entire cable is still only 1.7 cm.

Internal structure of a submarine cable containing several fibers: (1) insulating polyethylene; (2) copper tubing; (3) steel rods; (4) optical fibers in water-resistant jelly. The scale on the right shows the actual size (licensed under Public Domain via Wikimedia Commons)

After 1990, many laboratory experiments investigated whether the amplifier technology could be deployed for submarine cables such that the signal retained its optical form all along the cable length, thus avoiding the use of expensive in-line regenerators. As early as 1991, an experiment employed a recirculating-loop configuration to demonstrate the possibility of data transmission in this manner over 14,300 km at 5 Gbit/s. This experiment indicated that an all-optical, submarine transmission system was feasible for intercontinental communication. The TAT–12 cable, installed in 1995, employed optical amplifiers in place of in-line regenerators and operated at a bit rate of 5.3 Gbit/s with an amplifier spacing of about 50 km. The actual bit rate was slightly larger than the data rate of 5 Gbit/s because of the overhead associated with the forward-error correction that was necessary for the system to work. The design of such lightwave systems becomes quite complex because of the cumulative effects of fiber dispersion and nonlinearity, which must be controlled over long distances.

International submarine cable network of fiber-optic communication systems around 2015 ( source : dataset encoded by Greg Mahlknecht, http://www.cablemap.info )

The use of the WDM technique after 1996 in combination with optical amplifiers, dispersion management, and error correction revolutionized the design of submarine fiber-optic systems. In 1998, a submarine cable known as AC–1 was deployed across the Atlantic Ocean with a capacity of 80 Gb/s using the WDM technology. An identically designed system (PC–1) crossed the Pacific Ocean. The use of dense WDM, in combination with multiple fiber pairs per cable, resulted in systems with large capacities. After 2000, several submarine systems with a capacity of more than 1 Tbit/s became operational (see Table  8.2 ). Figure  8.17 shows the international submarine cable network of fiber-optic communication systems. The VSNL transatlantic submarine system installed in 2001 had a total capacity of 2.56 Tbit/s and spans a total distance of 13,000 km. A submarine system, known as India-ME-WE and installed in 2009, is capable of operating bidirectionally at 3.84 Tb/s through four fiber pairs. By 2012, submarine systems with a total capacity of 5 Tbit/s for traffic in each direction became operational. A proposed system, known as Arctic Fiber, will be capable of carrying traffic at speeds of up to 8 Tbit/s by transmitting 50 channels (each operating at 40 Gb/s) over four fiber pairs. It is estimated that more than 400 million kilometers of optical fiber have already been deployed worldwide, a number that is close to three times the distance to sun.

7 Conclusions

This chapter began with a brief history of optical communication before describing the main components of a modern optical communication system. Specific attention was paid to the development of low-loss optical fibers as they played an essential role after 1975. I describe in detail the evolution of fiber-optic communication systems through its six generations over a 40-year time period ranging from 1975 to 2015. I also discuss how the adoption of WDM during the 1990s was fueled by the advent of the Internet and how it eventually led in 2000 to bursting of the telecom bubble in the stock markets worldwide. However, the telecommunication industry recovered by 2005, and the researchers have come up with new techniques during the last 10 years. Recent advances brought by digital coherent technology and space-division multiplexing are described briefly in this chapter. Figure  8.17 shows the international submarine cable network of fiber-optic communication systems that allows the Internet to operate transparently, interconnecting computers worldwide on demand. Such a global high-speed network would have not been possible without the development of fiber-optic communication technology during the 1980s and the adoption of the WDM technique during the decade of the 1990s. One can only wonder what the future holds, especially if the potential of the SDM technology is realized by the year 2020.

Huurdeman AA (2003) The worldwide history of telecommunications. Wiley, Hoboken, NJ

Book   Google Scholar  

Agrawal GP (2010) Fiber-optic communication systems, 4th edn. Wiley, Hoboken, NJ

Chappe I. (1824) Histoire de la télégraphie (in French), University of Michigan Library

Google Scholar  

Holzmann GJ, Pehrson B (2003) The early history of data networks. Wiley, Hoboken, NJ

Jones A (1852) Historical sketch of the electrical telegraph. Putnam, New York

Bell AG (1876) Improvement in telegraphy, U.S. Patent No. 174,465

Pratt WK (1969) Laser communication systems. Wiley, Hoboken, NJ

Miller SE (1966) Communication by laser. Sci Am 214:19–25

Article   ADS   Google Scholar  

Hecht J (1999) City of light: the story of fiber optics. Oxford University Press, New York

Kao KC, Hockham GA (1966) Dielectric-fiber surface waveguides for optical frequencies. Proc IEE 113:1151–1158

http://www.nobelprize.org/nobel_prizes/physics/laureates/2009/

Kapron FP, Keck DB, Maurer RD (1970) Radiation losses in glass optical waveguides. Appl Phys Lett 17:423–425

Miya T, Terunuma Y, Hosaka T, Miyoshita T (1979) Ultimate low-loss single-mode fiber at 1.55 μm. Electron Lett 15:106–108

Alferov Z. (2000) Double heterostructure lasers: early days and future perspectives. IEEE J Sel Top Quant Electron 6:832–840

Article   Google Scholar  

Hayashi I, Panish MB, Foy PW, Sumski S (1970). Junction lasers which operate continuously at room temperature. Appl Phys Lett 17:109–111

Willner AE (ed.) (2000) Several historical articles in this millennium issue cover the development of lasers and optical fibers. IEEE J Sel Top Quant Electron 6:827–1513

Kogelnik H (2000) High-capacity optical communications: personal recollections. IEEE J Sel Top Quant Electron 6:1279–1286

Fukuchi K, Kasamatsu T, Morie M, Ohhira R, Ito T, Sekiya K, Ogasahara D, Ono T (2001) 10.92-Tb/s (273 × 40-Gb/s) triple-band/ultra-dense WDM optical-repeatered transmission experiment. In: Proceedings of the Optical Fiber Communication (OFC) conference, paper PD24

Essiambre R-J, Tkach RW (2012) Capacity trends and limits of optical communication networks. Proc IEEE 100:1035–1055

Zhou X et al (2011) 64-Tb/s, 8 b/s/Hz, PDM-36QAM transmission over 320 km using both pre- and post-transmission digital signal processing. J Lightwave Technol 29:571–577

Shannon CE (1948) A mathematical theory of communication. Bell Syst Tech J 27:379–423

Article   MathSciNet   MATH   Google Scholar  

Essiambre R-J, Kramer G, Winzer PJ, Foschini GJ, Goebel B (2010) Capacity limits of optical fiber networks. J. Lightwave Technol. 28:662–701

Ryf R et al (2012) Mode-division multiplexing over 96 km of few-mode fiber using coherent 6 × 6 MIMO processing. J. Lightwave Technol. 30:521–531

Takara H et al (2012) 1.01-Pb/s crosstalk-managed transmission with 91.4-b/s/Hz aggregated spectral efficiency. In: Proceedings of the European conference on optical communications, paper Th3.C.1

Richardson DJ, Fini JM, Nelson LE (2012) Space-division multiplexing in optical fibres. Nat Photon 7:354–362

Li G, Bai N, Zhao N, Xia C (2014) Space-division multiplexing: the next frontier in optical communication. Adv Opt Commun 6:413–487

Fontaine NK et al (2015) 30×30 MIMO Transmission over 15 Spatial Modes. In: Proceedings of the Optical Fiber Communication (OFC) conference, post deadline paper Th5C.1

Download references

Acknowledgements

The author thanks Dr. R.-J. Essiambre of Alcatel–Lucent Bell Laboratories for helpful suggestions. The financial support of US National Science Foundation is also gratefully acknowledged.

Author information

Authors and affiliations.

The Institute of Optics, University of Rochester, Rochester, NY, 14627, USA

Govind P. Agrawal

You can also search for this author in PubMed   Google Scholar

Corresponding author

Correspondence to Govind P. Agrawal .

Editor information

Editors and affiliations.

National Center for Applied Physics, King Abdulaziz City for Science and Technology, Riyadh, Saudi Arabia

Mohammad D. Al-Amri

Department of Electronics, University of York, Heslington, United Kingdom

Mohamed El-Gomati

Department of Physics and Astronomy, Texas A&M University, College Station, Texas, USA

M. Suhail Zubairy

Rights and permissions

Open Access This chapter is distributed under the terms of the Creative Commons Attribution 4.0 International License ( http://creativecommons.org/licenses/by/4.0/ ), which permits use, duplication, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, a link is provided to the Creative Commons license and any changes made are indicated.

The images or other third party material in this chapter are included in the work’s Creative Commons license, unless indicated otherwise in the credit line; if such material is not included in the work’s Creative Commons license and the respective action is not permitted by statutory regulation, users will need to obtain permission from the license holder to duplicate, adapt or reproduce the material.

Reprints and permissions

Copyright information

© 2016 The Author(s)

About this chapter

Agrawal, G.P. (2016). Optical Communication: Its History and Recent Progress. In: Al-Amri, M., El-Gomati, M., Zubairy, M. (eds) Optics in Our Time. Springer, Cham. https://doi.org/10.1007/978-3-319-31903-2_8

Download citation

DOI : https://doi.org/10.1007/978-3-319-31903-2_8

Published : 14 December 2016

Publisher Name : Springer, Cham

Print ISBN : 978-3-319-31902-5

Online ISBN : 978-3-319-31903-2

eBook Packages : Physics and Astronomy Physics and Astronomy (R0)

Share this chapter

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

• Publish with us

Policies and ethics

• Find a journal
• Track your research

• Create Account

Main navigation dropdown

Publications, recent advances in optical wireless communications for 6g, wlans and beyond, publication date, october 2023, manuscript submission deadline, 15 february 2023, call for papers.

Fast-evolving user practices of newer information creation, sensing, sharing, and consumption in our community, business, and industry have stimulated a huge surge in data traffic with heterogeneous quality of user experience requirements. To cater to these changes, next generation communication networks need to be endowed with the capability of providing high data rate, stringent latency, and ubiquitous services. Optical wireless communication systems are being actively developed to derive the combined benefits from advanced optical and wireless technologies. With the inherent advantages, such as ultra-high bandwidth, long communication distance, and strong data privacy, optical wireless systems will become an essential building block of the future communication network infrastructure. Optical wireless communications will play an important role in network operations for 6G, WLANs, AR/VR, and beyond. Optical wireless system design and coordination is also an open topic.

The field of optical wireless communication and network systems has evolved beyond classical communication and network applications and the technologies involve deeper science principles. On one hand, besides renewed interest from Electrical Communication Engineering, Computer Engineering, Computer Science and AI communities, many of the technological advances draw learnings from the newer findings in Applied Sciences, such as, Engineering Physics and Optoelectronics. On the other hand, the applications of optical communication technologies continue to transcend beyond conventional high speed data communication. Terahertz communications, holographic representation, optical meta-materials based reconfigurable intelligent surface for beamforming, are a few example uses of advanced technologies towards fulfilling future-generation multi-disciplinary applications. This special issue is aimed to capture the advances in optical wireless communication technologies and the associated future multi-disciplinary applications.

This Special Issue is an avenue to explore the applications of optical wireless communications in emerging networks and services. It will present the latest research and technology development endeavors, network design, as well as system implementation in the advanced fields of holographic representation, terahertz communication, visible light communication, underwater communication, and low-earth orbit (LEO) satellite connectivity. These technical advances are promising in developing 6G, WiFi 8, AR/VR, and other network and service solutions. This Special Issue will also report investigations on theoretical and practical challenges to encourage joint efforts from both academia and industry. The topics of interest include, but not limited to:

• Challenges and new advances of optical wireless technologies
• Optical wireless solutions for 6G and WLANs
• New applications of optical wireless communications in AR/VR, AI, IoT, Industry 4.0
• Software defined optical wireless network with AI
• Fiber to the Room (FTTR), WiFi and PON integration, and Fixed 6G
• Optical wireless communication for space-air-ground integrated network
• Optical wireless system management, optimization, data security and reliability
• Energy transfer, harvesting and saving in optical wireless systems
• Optical reconfigurable intelligent surface aided communications
• Standards and recommendations on optical wireless communications
• Experiments, trials, testbeds, and integration of optical wireless systems

Submission Guidelines

Prospective authors should prepare their submissions in accordance with the rules specified in the Information for Authors of the IEEE Wireless Communications guidelines .

Authors should submit a PDF version of their complete manuscript to Manuscript Central . The timetable is as follows:

Important Dates

Manuscript Submission Deadline: 15 February 2023 (Extended Deadline) Initial Decision Date: 1 April 2023 Revised Manuscript Due: 1 May 2023 Final Decision Date: 1 June 2023 Final Manuscript Due: 1 August 2023 Publication Date: October 2023

Guest Editors

Yuanqiu Luo Futurewei Technologies, USA

Admela Jukan Technical University of Braunschweig, Germany

Krishna M. Sivalingam Indian Institutes of Technology Madras, India

Xiaojun (Matt) Cao Georgia State University, USA

Suresh Subramaniam George Washington University, USA

Gangxiang (Steven) Shen Soochow University, China

Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

• View all journals
• Explore content
• About the journal
• Publish with us
• Sign up for alerts

Fibre optics and optical communications articles within Scientific Reports

Article 10 May 2024 | Open Access

Low-complexity continuous-variable quantum key distribution with true local oscillator using pilot-assisted frequency locking

• Andres Ruiz-Chamorro
• , Aida Garcia-Callejo
•  &  Veronica Fernandez

Article 30 April 2024 | Open Access

A new gas detection technique through cross-correlation with a complex aperiodic FBG

• Matthew Rahme
• , Peter Tuthill
•  &  Sergio Leon-Saval

Article 22 April 2024 | Open Access

All-fiber few-mode interference for complex azimuthal pattern generation

• Josué I. Gómez-Méndez
• , Rodolfo A. Carrillo-Betancourt
•  &  Juan Hernández-Cordero

Article 11 April 2024 | Open Access

Emission of five OAM dispersive waves in dispersion-engineered double-ring core fiber

• , Yuxi Fang
•  &  Yang Yue

Article 29 March 2024 | Open Access

Single-step phase identification and phase locking for coherent beam combination using deep learning

• , Fedor Chernikov
•  &  Michalis N. Zervas

Article 28 March 2024 | Open Access

Multimodal fiber probe for simultaneous mid-infrared and Raman spectroscopy

• Alexander Novikov
• , Stanislav Perevoschikov
•  &  Andrey Bogomolov

Article 25 March 2024 | Open Access

Advancing high-performance visible light communication with long-wavelength InGaN-based micro-LEDs

• Fu-He Hsiao
• , Wen-Chien Miao
•  &  Yu-Heng Hong

Article 08 March 2024 | Open Access

Line-wave waveguide engineering using Hermitian and non-Hermitian metasurfaces

• Haddi Ahmadi
• , Zahra Ahmadi
•  &  Homayoon Oraizi

Article 22 February 2024 | Open Access

Conflict-free joint decision by lag and zero-lag synchronization in laser network

• , Takatomo Mihana
•  &  Makoto Naruse

Article 08 February 2024 | Open Access

Inkjet-printed high-performance and mechanically flexible organic photodiodes for optical wireless communication

• Luis Arturo Ruiz‐Preciado
• , Petr Pešek
•  &  Gerardo Hernandez-Sosa

Article 09 January 2024 | Open Access

High-dimensional single photon based quantum secure direct communication using time and phase mode degrees

• Byungkyu Ahn
• , Jooyoun Park
•  &  Sangrim Lee

Article 08 January 2024 | Open Access

Research on the variation law of floor stress information entropy in upper protective layer mining based on Brillouin optical fiber sensing

• , Gaoyi Yang
•  &  Mingyue Weng

Article 21 December 2023 | Open Access

Tailoring ultrabroadband near‐infrared luminescence in Bi-doped germanosilicate glasses

• A. Mehaboob
• , V. Fuertes
•  &  Y. Messaddeq

Article 06 December 2023 | Open Access

Practical, high-speed Gaussian coherent state continuous variable quantum key distribution with real-time parameter monitoring, optimised slicing, and post-processed key distillation

• Amanda Weerasinghe
• , Muataz Alhussein
•  &  Richard Penty

Article 16 October 2023 | Open Access

Systematic-error suppression in low-coherence Brillouin optical correlation-domain reflectometry

• Kenta Otsubo
• , Guangtao Zhu
•  &  Yosuke Mizuno

Article 14 October 2023 | Open Access

High resolution seafloor thermometry for internal wave and upwelling monitoring using Distributed Acoustic Sensing

• Julián David Pelaez Quiñones
• , Anthony Sladen
•  &  Paschal Coyle

Article 12 October 2023 | Open Access

Near-infrared spectroscopy of low-transmittance samples by a high-power time-stretch spectrometer using an arrayed waveguide grating (AWG)

• Hiroyuki Kawagoe
• , Hideyuki Sera
•  &  Go Yamada

Article 22 September 2023 | Open Access

Phase encoded quantum key distribution up to 380 km in standard telecom grade fiber enabled by baseline error optimization

• Nishant Kumar Pathak
• , Sumit Chaudhary
•  &  Bhaskar Kanseri

Article 20 September 2023 | Open Access

Convolutional neural networks for mode on-demand high finesse optical resonator design

• Denis V. Karpov
• , Sergei Kurdiumov
•  &  Peter Horak

Article 19 September 2023 | Open Access

Enhanced spectroelectrochemistry with lossy-mode resonance optical fiber sensor

• Monika Janik
• , Katarzyna Lechowicz
•  &  Mateusz Śmietana

Article 13 September 2023 | Open Access

A novel velocity band energy workflow for fiber-optic DAS interpretation and multiphase flow characterization

• Gerald. K. Ekechukwu
• , Jyotsna Sharma
•  &  Michael J. William

Article 25 August 2023 | Open Access

Periodic liquid crystalline waveguiding microstructures

• Sławomir Ertman
• , Kamil Orzechowski
•  &  Tomasz R. Woliński

Outdoor mm-wave 5G/6G transmission with adaptive analog beamforming and IFoF fronthaul

• Javier Pérez Santacruz
• , Elmine Meyer
•  &  Simon Rommel

Article 09 August 2023 | Open Access

Towards REPO 4 nanocrystal-doped optical fibers for distributed sensing applications

• , N. Grégoire

Article 29 July 2023 | Open Access

Technical–economic analysis to identify the acceptable maximum attenuation on PON FTTH lines for wholesale network operators

• Claudio Mazzei
• , Matteo Crescitelli
•  &  Francesca Brunetti

Article 16 June 2023 | Open Access

Photo-elasticity of silk fibroin harnessing whispering gallery modes

• Nikolaos Korakas
• , Davide Vurro
•  &  Stavros Pissadakis

Article 31 May 2023 | Open Access

The role of tungsten oxide in Er 3+ -doped bismuth-germanate glasses for optical amplification in L-band

• Hüseyin Can Çamiçi
• , Théo Guérineau
•  &  Younès Messaddeq

Article 16 May 2023 | Open Access

On multiplexing in physical random number generation, and conserved total entropy content

• Frederic Monet
•  &  Raman Kashyap

Article 13 March 2023 | Open Access

Gecko-inspired self-adhesive packaging for strain-free temperature sensing based on optical fibre Bragg gratings

• Shuochao Liu
• , Pingyu Zhu
•  &  Marcelo A. Soto

Article 27 January 2023 | Open Access

Low-volume label-free SARS-CoV-2 detection with the microcavity-based optical fiber sensor

• , Tomasz Gabler

Article 24 January 2023 | Open Access

Efficient dynamic channel assignment through laser chaos: a multiuser parallel processing learning algorithm

• Zengjing Chen
•  &  Chengzhi Xing

Article 09 January 2023 | Open Access

Performance investigations on data protection algorithms in generalized multi protocol label switched optical networks

• , Simranjit Singh
•  &  Amit Wason

Article 03 December 2022 | Open Access

Fiber-based 3D nano-printed holography with individually phase-engineered remote points

• Malte Plidschun
• , Matthias Zeisberger
•  &  Markus A. Schmidt

Article 31 October 2022 | Open Access

Demonstration of 100 Gbps coherent free-space optical communications at LEO tracking rates

• Shane M. Walsh
• , Skevos F. E. Karpathakis
•  &  Sascha W. Schediwy

Article 27 October 2022 | Open Access

Programmable and tunable flat-top supercontinuum laser sources via electro-optic intensity and phase modulation scheme

• Minhyup Song
• , Minje Song
•  &  Joon Tae Ahn

Article 30 September 2022 | Open Access

Integrated optical frequency comb for 5G NR Xhauls

• Eduardo Saia Lima
• , Ramon Maia Borges
•  &  Arismar Cerqueira Sodré Jr

Article 17 August 2022 | Open Access

Sensitive seismic sensors based on microwave frequency fiber interferometry in commercially deployed cables

• Adonis Bogris
• , Thomas Nikas
•  &  Ioannis Chochliouros

Article 26 July 2022 | Open Access

Data-driven model discovery of ideal four-wave mixing in nonlinear fibre optics

• Andrei V. Ermolaev
• , Anastasiia Sheveleva
•  &  John M. Dudley

Article 11 June 2022 | Open Access

Rapid and sensitive magnetic field sensor based on photonic crystal fiber with magnetic fluid infiltrated nanoholes

• , Satyendra Kumar Mishra
•  &  Bora Ung

Article 09 June 2022 | Open Access

Coherent photonic Terahertz transmitters compatible with direct comb modulation

• Luis Gonzalez-Guerrero
•  &  Guillermo Carpintero

Article 19 May 2022 | Open Access

Multi-dimensional quantitative model of communication network value

• , Chaoqin Gan
•  &  Jianqiang Hui

Article 13 May 2022 | Open Access

Serial and parallel convolutional neural network schemes for NFDM signals

• Wen Qi Zhang
• , Terence H. Chan
•  &  Shahraam Afshar Vahid

Article 23 March 2022 | Open Access

A lensed fiber Bragg grating-based membrane-in-the-middle optomechanical cavity

• Joris Baraillon
• , Boris Taurel
•  &  Laurent Duraffourg

Article 16 March 2022 | Open Access

Infinity additive manufacturing of continuous microstructured fiber links for THz communications

• , Kathirvel Nallappan
•  &  Maksim Skorobogatiy

Article 14 March 2022 | Open Access

Probing the dispersive properties of optical fibers with an array of femtosecond-written fiber Bragg gratings

• Tommy Boilard
• , Réal Vallée
•  &  Martin Bernier

Article 03 March 2022 | Open Access

A Lab-in-a-Fiber optofluidic device using droplet microfluidics and laser-induced fluorescence for virus detection

• Helen E. Parker
• , Sanghamitra Sengupta
•  &  Fredrik Laurell

Article 17 February 2022 | Open Access

Fractal, diffraction-encoded space-division multiplexing for FSO with misalignment-robust, roaming transceivers

• Xiaojing Weng
•  &  Luat T. Vuong

Article 15 February 2022 | Open Access

Comprehensive deep learning model for 3D color holography

• Alim Yolalmaz
•  &  Emre Yüce

Article 24 January 2022 | Open Access

Coupled-core fiber Bragg gratings for low-cost sensing

• Jose A. Flores-Bravo
• , Javier Madrigal
•  &  Joel Villatoro

Article 20 January 2022 | Open Access

Quasi-perfect vortices generated by Pancharatnam-Berry phase metasurfaces for optical spanners and OAM communication

• Xiang Zhiyuan
•  &  Shen Yaochun

Browse broader subjects

• Applied optics

Quick links

• Explore articles by subject
• Guide to authors
• Editorial policies

• Frontiers in Communications and Networks
• Optical Communications and Networks
• Research Topics

Optical Wireless Communication Technologies

Total Downloads

Total Views and Downloads

About this Research Topic

Optical Wireless Communication (OWC) is a line-of-sight wireless communication system in which data is transmitted in the form of laser beams. OWC is one of the best communication systems because of its high bandwidth, permissionless, highest transfer data rate, and ultra-high security. The development of OWC has increased extensively over the past decade, aided by the availability of powerful system components developed for the field of optical fiber communications. OWCs mainly pass through channels such as free space, the earth's atmosphere, seawater, and interstellar space. However, the channel environment, such as the atmosphere, will seriously affect the wavefront performance of light, causing intersymbol crosstalk and resulting in an increase in the communication bit error rate (BER). Therefore, how to improve the communication performance of OWC in different channels is a focus of researchers. The current research on OWC technology mainly focuses on an advanced optical terminal and photoelectric system fusion design to improve the signal-to-noise ratio of light, using an efficient pointing acquiring and tracking (APT) unit to obtain better beam pointing, and studying the influence of atmospheric turbulence and seawater channels on the performance of light waves for obtaining optimal design parameters. There is also a focus on employing advanced modulation, demodulation and error correction coding technology to get higher transmission rate and lower BER, studying OWC ad hoc network protocols and advanced network topology structure to achieve the purpose of networking applications, and so on. This Research Topic will therefore discuss the related technologies of OWC, so that researchers can better understand the composition of OWC technology, grasp the latest trends in OWC technology development, and achieve the goal of promoting the development of OWC technology. We seek high-quality submissions related to (but not limited to) one or more of the following topics: ● Present and future optical wireless communication terminals, systems and links ● Atmospheric propagation, transmission effects and compensation techniques ● Adaptive optics technology in OWCs ● Advanced optical signal processing technologies ● Optical communication ad hoc network and network topology ● Visible light and underwater optical communication technologies Researchers are encouraged to submit complete unpublished papers, exploring emerging technologies in Optical Wireless Communication.

Keywords : optical wireless communications, optical signal processing, optical communication network, optical propagation, adaptive optics

Important Note : All contributions to this Research Topic must be within the scope of the section and journal to which they are submitted, as defined in their mission statements. Frontiers reserves the right to guide an out-of-scope manuscript to a more suitable section or journal at any stage of peer review.

Topic Editors

Topic coordinators, submission deadlines, participating journals.

Manuscripts can be submitted to this Research Topic via the following journals:

total views

• Demographics

No records found

total views article views downloads topic views

Top countries

Top referring sites, about frontiers research topics.

With their unique mixes of varied contributions from Original Research to Review Articles, Research Topics unify the most influential researchers, the latest key findings and historical advances in a hot research area! Find out more on how to host your own Frontiers Research Topic or contribute to one as an author.

Researchers demonstrate 40-channel optical communication link

Silicon-based device could help meet ever-growing need to move more data faster.

Researchers have demonstrated a silicon-based optical communication link that combines two multiplexing technologies to create 40 optical data channels that can simultaneously move data. The new chip-scale optical interconnect can transmit about 400 GB of data per second -- the equivalent of about 100,000 streaming movies. This could improve data-intensive internet applications from video streaming services to high-capacity transactions for the stock market.

"As demands to move more information across the internet continue to grow, we need new technologies to push data rates further," said Peter Delfyett, who led the University of Central Florida College of Optics and Photonics (CREOL) research team. "Because optical interconnects can move more data than their electronic counterparts, our work could enable better and faster data processing in the data centers that form the backbone of the internet."

A multi-institutional group of researchers describes the new optical communication link in the Optica Publishing Group journal Optics Letters . It achieves 40 channels by combining a frequency comb light source based on a new photonic crystal resonator developed by the National Institute of Standards and Technology (NIST) with an optimized mode-division multiplexer designed by the researchers at Stanford University. Each channel can be used to carry information much like different stereo channels, or frequencies, transmit different music stations.

"We show that these new frequency combs can be used in fully integrated optical interconnects," said Chinmay Shirpurkar, co-first author of the paper. "All the photonic components were made from silicon-based material, which demonstrates the potential for making optical information handling devices from low-cost, easy-to-manufacture optical interconnects."

In addition to improving internet data transmission, the new technology could also be used to make faster optical computers that could provide the high levels of computing power needed for artificial intelligence, machine learning, large-scale emulation and other applications.

Using multiple light dimensions

The new work involved research teams led by Firooz Aflatouni of the University of Pennsylvania, Scott B. Papp from NIST, Jelena Vuckovic from Stanford University and Delfyett from CREOL. It is part of the DARPA Photonics in the Package for Extreme Scalability (PIPES) program, which aims to use light to vastly improve the digital connectivity of packaged integrated circuits using microcomb-based light sources.

The researchers created the optical link using tantalum pentoxide (Ta 2 O 5 ) waveguides on a silicon substrate fabricated into a ring with a nanopatterned oscillation on the inner wall. The resulting photonic crystal micro-ring resonator turns a laser input into ten different wavelengths. They also designed and optimized a mode-division multiplexer that transforms each wavelength into four new beams that each have different shapes. Adding this spatial dimension enables a fourfold increase in data capacity, creating the 40 channels.

Once the data is encoded onto each beam shape and each beam color, the light is recombined back into a single beam and transmitted to its destination. At the final destination, the wavelengths and beam shapes are separated so that each channel can be received and detected independently, without interference from the other transmitted channels.

"An advantage of our link is that the photonic crystal resonator enables easier soliton generation and a flatter comb spectrum than those demonstrated with conventional ring resonators," said co-first author Jizhao Zang from NIST. "These features are beneficial for optical data links."

Better performance with inverse design

To optimize the mode division multiplexer, the researchers used a computational nanophotonic design approach called photonic inverse-design. This method provides a more efficient way to explore a full range of possible designs while offering smaller footprints, better efficiencies and new functionalities.

"The photonic inverse-design approach makes our link highly customizable to meet the needs of specific applications," said co-first author Kiyoul Yang from Stanford University.

Tests of the new device matched well with simulations and showed that the channels exhibited a low crosstalk of less than -20 dB. Using less than ?10 dBm of received optical receiver power, the link performed error-free data transmission in 34 out of the 40 channels using a PRBS31 pattern, a standard used to test high-speed circuits under stress.

The researchers are now working to further improve the device by incorporating photonic crystal micro-ring resonators that produce more wavelengths or by using more complex beam shapes. Commercializing these devices would require the full integration of a transmitter and receiver chip with high bandwidth, low power consumption and a small footprint. This could enable the next generation of optical interconnects for use in data-center networks.

Open-source code for the photonic optimization software used in the paper is available at https://github.com/stanfordnqp/spins-b .

• Telecommunications
• Electronics
• Biochemistry
• Information Technology
• Computers and Internet
• Voice over IP
• World Wide Web
• Stock market
• Massively multiplayer online game
• Quantum computer
• Information and communication technologies
• The Long Tail

Story Source:

Materials provided by Optica . Note: Content may be edited for style and length.

Journal Reference :

• C. Shirpurkar, J. Zang, K. Y. Yang, D. Carlson, S. P Yu, E. Lucas, S. V. Pericherla, J. Yang, M. Guidry, D. Lukin, G. H. Ahn, J. Lu, L. Trask, F. Aflatouni, J. Vučković, S. B. Papp, P. J. Delfyett. Photonic crystal resonators for inverse-designed multi-dimensional optical interconnects . Optics Letters , 2022; 47 (12): 3063 DOI: 10.1364/OL.461272

Cite This Page :

Explore More

• Fastest Rate of CO2 Rise Over Last 50,000 Years
• Like Dad and Like Mum...all in One Plant
• What Makes a Memory? Did Your Brain Work Hard?
• Plant Virus Treatment for Metastatic Cancers
• Controlling Shape-Shifting Soft Robots
• Brain Flexibility for a Complex World
• ONe Nova to Rule Them All
• AI Systems Are Skilled at Manipulating Humans
• Planet Glows With Molten Lava
• A Fragment of Human Brain, Mapped

Trending Topics

Strange & offbeat.

• Keep it simple - don't use too many different parameters.
• Example: (diode OR solid-state) AND laser [search contains "diode" or "solid-state" and laser]
• Example: (photons AND downconversion) - pump [search contains both "photons" and "downconversion" but not "pump"]
• Improve efficiency in your search by using wildcards.
• Asterisk ( * ) -- Example: "elect*" retrieves documents containing "electron," "electronic," and "electricity"
• Question mark (?) -- Example: "gr?y" retrieves documents containing "grey" or "gray"
• Use quotation marks " " around specific phrases where you want the entire phrase only.
• For best results, use the separate Authors field to search for author names.
• Use these formats for best results: Smith or J Smith
• Use a comma to separate multiple people: J Smith, RL Jones, Macarthur
• Note: Author names will be searched in the keywords field, also, but that may find papers where the person is mentioned, rather than papers they authored.
• Optical Fiber Communication Conference (OFC) 2024
• Technical Digest Series (Optica Publishing Group, 2024),
• paper M3F.2
• • https://doi.org/10.1364/OFC.2024.M3F.2

VCSEL-Based Optical Wireless Transmission: New Research Prospects

Ernesto Ciaramella, Giulio Cossu, and Lorenzo Gilli

Author Affiliations

Ernesto Ciaramella, * Giulio Cossu, and Lorenzo Gilli

Scuola Superiore Sant’Anna, Pisa, ( Italy)

* Corresponding author: [email protected]

• E Ciaramella
• San Diego California United States
• 24–28 March 2024
• ISBN: 978-1-957171-32-6

From the session Radio-Over-Fiber and 6G Access (M3F)

Your library or personal account may give you access

• Optical Fiber Communication Conference (OFC) 2024 , Technical Digest Series (Optica Publishing Group, 2024), paper M3F.2.%0Ahttps://opg.optica.org/abstract.cfm?URI=OFC-2024-M3F.2%0A---------------------------------------------------------------------------%0AThis is sent to you as an email notification feature from Optica Publishing Group: https://opg.optica.org"> Email
• Share with Facebook
• Post on reddit
• Share with LinkedIn
• Add to Mendeley

• Share with WeChat
• Endnote (RIS)
• Citation alert
• Save article
• Fiber optic communications
• Laser communications
• Optical filters
• Optical properties
• Optical wireless communication
• References ( 14 )
• Back to Top

The fundamental features of VCSELs make them very suitable for various types of optical wireless communications, especially over short links. We present a range of promising applications for these devices in new OWC areas.

© 2024 The Author(s)

Ernesto Ciaramella, Giulio Cossu, Alessandro Messa, and Alessandro Sturniolo T1B.3 Asia Communications and Photonics Conference (ACP) 2019

Zhiyuan Cao, Shi Zhang, Zixian Wei, Li Zhang, Zhaoming Wang, H. Y. Fu, and Yuhan Dong M4A.312 Asia Communications and Photonics Conference (ACP) 2020

Ke Wang, Tingting Song, Yitong Wang, Chengwei Fang, Ampalavanapillai Nirmalathas, Christina Lim, Elaine Wong, and Sithamparanathan Kandeepan Tu3C.4 Optical Fiber Communication Conference (OFC) 2022

Xu Liu, Lin Ma, Ying Shi, Qiancheng Yu, Motoya Kaneta, and Zuyuan He W2A.6 Optical Fiber Communication Conference (OFC) 2024

Antonio Malacarne, Alberto Montanaro, Fawad Ahmad, Gaurav Pandey, Antonio D’Errico, Marco Romagnoli, Antonella Bogoni, and Claudio Porzi M4J.6 Optical Fiber Communication Conference (OFC) 2024

Optical Fiber Communication Conference 2024

• From the session  Radio-Over-Fiber and 6G Access (M3F)

Confirm Citation Alert

Field error.

• Publishing Home
• Conferences
• Preprints (Optica Open)
• Information for
• Open Access Information
• Open Access Statement and Policy
• Terms for Journal Article Reuse
• Other Resources
• Optica Open
• Optica Publishing Group Bookshelf
• Optics ImageBank
• Optics & Photonics News
• Spotlight on Optics
• Optica Home
• About Optica Publishing Group
• About My Account
• Sign up for Alerts
• Send Us Feedback
• Go to My Account
• Login to access favorites
• Recent Pages

Login or Create Account

A Survey of Free Space Optics (FSO) Communication Systems, Links, and Networks

Ieee account.

• Change Username/Password
• Update Address

Purchase Details

• Payment Options
• Order History
• View Purchased Documents

Profile Information

• Communications Preferences
• Profession and Education
• Technical Interests
• US & Canada: +1 800 678 4333
• Worldwide: +1 732 981 0060
• Contact & Support
• About IEEE Xplore
• Accessibility
• Terms of Use
• Nondiscrimination Policy
• Privacy & Opting Out of Cookies

A not-for-profit organization, IEEE is the world's largest technical professional organization dedicated to advancing technology for the benefit of humanity. © Copyright 2024 IEEE - All rights reserved. Use of this web site signifies your agreement to the terms and conditions.